-v1665700116905.png?500x500&options=w_150){kind=icon}
Anton Bauer D-Box V-Mount for Sony (Venice)
D-Box (Sony Venice, V-Mount) adds power distribution, standardized remote start/stop, and hot swap abilities for the Sony Venice camera. The D-Box main unit attaches to the back of the AXS-R7 or to the V-Mount plate on the camera rear and the Power Strip portion attaches to the top right side of the camera via a 3pin Fischer and the tape hook threaded hole. Connectors on the D-Box Power Strip are contoured to match the camera profile and connector angle which allows for all cables to be installed with no obstructions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port including the ARRI UMC-4 / WCU-4. The DC input on the D-Box is the same as the camera's 4pin XLR connector allowing for an AC power supply, external power plate, or VCLX block battery to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the onboard battery fully charged. Physical fuses have been replaced by a processor controlled amp limit which is settable to 3.8, 5.8, or 9 amps using the slide switch on the operator's side. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. The "DC IN" and "BATT" LEDs are dual LEDs. This means the LED If battery voltage is above 12.5V the LED will be green. If the battery voltage is below 12V the LED will be red. If the battery voltage is between those values the LED will be orange (red + green). Flashing may occur during phase transition. Highest quality Anton/Bauer components are used in the V-Mount assembly and the unibody power plate design is both extremely durable and lightweight.
Compatibility
Anton Bauer D-Box V-Mount for Sony (Venice)
Request a Price Match
Fill out the price match form below, and we will be in touch shortly.
Lexar Professional Silver 128GB SDXC UHS-II 250MB/s Memory Card - V60
$89.00
Lexar Professional Silver 64GB SDXC UHS-II 250MB/s Memory Card - V60
$44.00
Lexar Professional Gold Series 128GB SDXC UHS-II 280MB/s Memory Card - V60
$99.00
Lexar Professional Silver 128GB SDXC UHS-I 160MB/s Memory Card - V30
$79.00
Lexar Professional Silver 256GB SDXC UHS-II 250MB/s Memory Card - V60
$149.00
Lexar Professional Gold 160GB CFexpress Type A 900MB/s Memory Card
$302.50
Recommended Accessories
Product Overview
D-Box (Sony Venice, V-Mount) adds power distribution, standardized remote start/stop, and hot swap abilities for the Sony Venice camera. The D-Box main unit attaches to the back of the AXS-R7 or to the V-Mount plate on the camera rear and the Power Strip portion attaches to the top right side of the camera via a 3pin Fischer and the tape hook threaded hole. Connectors on the D-Box Power Strip are contoured to match the camera profile and connector angle which allows for all cables to be installed with no obstructions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port including the ARRI UMC-4 / WCU-4. The DC input on the D-Box is the same as the camera's 4pin XLR connector allowing for an AC power supply, external power plate, or VCLX block battery to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the onboard battery fully charged. Physical fuses have been replaced by a processor controlled amp limit which is settable to 3.8, 5.8, or 9 amps using the slide switch on the operator's side. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. The "DC IN" and "BATT" LEDs are dual LEDs. This means the LED If battery voltage is above 12.5V the LED will be green. If the battery voltage is below 12V the LED will be red. If the battery voltage is between those values the LED will be orange (red + green). Flashing may occur during phase transition. Highest quality Anton/Bauer components are used in the V-Mount assembly and the unibody power plate design is both extremely durable and lightweight.
Need advice?
Speak to one of our dedicated Australian-based sales team members.
Request a Price Match
Fill out the price match form below, and we will be in touch shortly.
You may also like
Georges Cameras Gift Card - $100
Georges Cameras Gift Card - $200
Georges Cameras Gift Card - $50
Georges Cameras Gift Card - $500
Blog posts
LiDAR Autofocus Systems: DJI Focus Pro vs. PDMovie Live Air 3...
When it comes to LiDAR-based autofocus systems, both the DJI Focus Pro and the PDMovie Live Air 3 Smart bring cutting-edge technology to the table. These systems are designed for professionals...
View post
First look at the Sony A1 Mark II
The Sony Alpha 1 II: A New Era for Flagship Mirrorless Cameras We recently handed the Sony Alpha 1 II, Sony’s latest flagship full-frame mirrorless camera, to professional photographer Gracie Stendlfor a spin....
View post
First look at the new Sony G-Master 28-70mm F/2
You can pre-order through this link now — with bonus 86mm CPL and UV filters while stocks last! We will have this new lens in stores from mid-December. Sony has done it again...
View post
